CALL US
0086-371-60922096

Method to adjust the pulse amplitude and concrete pump

Pulse Diagnosis: How do we read the heart beat? (by Noah

Jul 30, 2009 · When taking the pulse the fingers can lie on the surface or press deeper to find different levels of the pulse. The change in the pressure on the vein, changes the meaning of the pulse. There are three levels of the pulse in this method. The first level is the superficial level, the way the pulse feels at the surface level of the wrist.

Learn More

Evaluation of Concrete Structure Using Nondestructive

Mar 10, 2019 · The resulting amplitude spectrum is used to determine the condition of the concrete. The tests were conducted at the grid points of a 0.6 x 0.6-m grid in five selected areas of the tunnels.

Learn More

A set of measures for the systematic classification of the

Feb 25, 2015 · For the pump P we use the fundamental compressional mode of a rod‐shaped sample driven to strain amplitudes 10 −7 ≤ϵ P <10 −5. The probe (p) is a HF pulse (of low strain amplitude, ϵ p ≃10 −7) that tests the state of the sample at all phases of the pump strain field, i.e., in both compression and tension. From the behavior of the

Learn More

Plasma optics in the context of high intensity lasers

Sep 23, 2019 · As we have seen in the initial stage (when the amplitude of the pump is much larger than that of the seed) the seed phase grows quickly while its amplitude does not change much. Indeed the seed phase grows as φ s ≃ 4 9 3 ( γ s c t ) 3, where γ sc depends on …

Learn More

Prediction on pipe flow of pumped concrete based on shear

Oct 01, 2013 · The concrete pump was a high pressure piston pump (model BSA2110HP-D, Putzmeister Co., Germany). Three different flow rates were studied as shown in Table 2. The filling rate of the pump cylinder, which directly affects the flow rate, was calibrated from specific experiments prior to the real concrete pumping.

Learn More

Concrete Detector U5200 Ultrasonic Flaw Detector,Concrete

4.Ultrasonic flat-measured method for testing crack depth of concrete surface (called 'crack test' for short); Features of Concrete Detector U5200 Ultrasonic Flaw Detector 1.During the test, the test result is available and the graphic distribution of abnormal points in each profile is shown at any time.

Learn More

Pundit 200 | Materials Testing | Geneq

The Pundit 200 is ideal for concrete properties analysis using ultrasound pulse velocity. Get a quote!

Learn More

METHOD AND DEVICE FOR STABILIZATION OF OPTICAL POWER …

1. A mode locked broadband ultrashort light pulse fiber oscillator based on nonlinear polarization rotation (NPR) of light comprising: a unidirectional fiber ring resonator operative to generate a train of ultrashort light pulses each having a broad range of frequencies, the fiber ring resonator including at least one light polarization controller unit; and an optoelectronic control feedback

Learn More

Fatigue life prediction for boom structure of concrete

Feb 01, 2016 · 2) Pumping mode: the outriggers unfold and support the equipment. The boom system unfolds and is adjusted to the desired position. Concrete in the hopper is pumped through the pumping system. The pumping mode is the primary mode of the concrete pump truck. The delivery cylinders deliver the concrete in the hopper to the delivery pipe (shown in

Learn More

Design and Analysis of Pendulum Operated Piston Pump

Nov 20, 2016 · Design and Analysis of Pendulum Operated Piston Pump ME Department, SRMGPC, Lucknow 40 3. It uses the minimum of human strength in comparison to present classic hand water pumps. 4. In comparison to the hand pumps the energy required to initiate the pumping process is significantly less for the pendulum pump.

Learn More

DAMAGE DETECTION TECHNIQUES FOR CONCRETE …

concrete pavements, and provides a wealth of data from a single measurement. Novel signal interpretation methods were developed for several important concrete applications. Detection of load-induced damage in a full-scale reinforced concrete column, as well as standard life-cycle damage in

Learn More

Example Lab Report (1).docx - Student Body Temperature

Pulse Amplitude Modulation. Pulse amplitude modulation is defined as the data transmission by altering the amplitudes (power levels or voltage) of every pulse in a regular time sequence of electromagnetic pulses. The possible number of amplitudes can be infinite, but mostly it is some power of two so that the final output signal can be digital.

Learn More

Experimental study on structural defect detection by

May 24, 2019 · The method is developed on the basis of the pulse-pre-pump Brillouin optical time domain analysis (PPP-BOTDA) method [21]. It employs the dynamic distributed measurement capability of the PPP-BOTDA in order to sense the structural damage under in-service operations. The method enables simultaneous detection of many defects for many types of

Learn More

Servo Motor Troubleshooting and Failure Analysis | ATO.com

paper, as shown in Figure 1. Concrete pump is widely used in tall buildings, bridges, and underground engi-neering projects to pump concrete to desired locations. The journal bearings are usually installed between each delivery pipe to adjust the direction of end hose. During pumping operation, concrete can be pumped continu-ously.

Learn More

Impact-Based Nonlinear Acoustic Testing for Characterizing

Jun 12, 2017 · Resonance-based methods, (linear) ultrasonic wave velocity and attenuation measurements and ultrasonic pulse-echo have long been adapted and used for concrete inspection. However, these conventional methods can only detect mm-size cracks, while showing no or little sensitivity to the accumulation of microcracks.

Learn More

From Fundamentals to Applications in Geotechnics doi:10

Pulse Amplitude Modulation - Circuit, Definition, Advantages, Types

Learn More

3D printing using concrete extrusion: A roadmap for

Oct 01, 2018 · Large-scale, cement-based additive manufacturing processes, often referred to as 3D concrete printing (3DCP), have been under development for the last 10 years and more than 30 groups world-wide are currently engaged in research. 3DCP disposes of the need for conventional moulds by precisely placing, or solidifying, specific volumes of material in sequential layers by a computer …

Learn More

Optimization of driven waveform of piezoelectric printhead

Jan 01, 2021 · The adjustment of the pulse amplitude was similar to the voltage setting method discussed in Section 4.2. The relationship between the drop mass and the voltage is shown in Fig. 7 . The following equation can be obtained via the interpolation method: (13) m A D M = k 2 U + b 2, where b 2 = - 17.25, and the slope was k 2 = 0.725 .

Learn More

From Fundamentals to Applications in Geotechnics doi:10

amplitude as the initial pulse, so the Beta method can be applied. Briefly, β is the rate of impedance change from Z2 to Z1 [4]: β = Z2 Z1 = 1 - α 1 + α (2) where: α is the damage amplitude divided by twice the amplitude of the initial pulse. Beta analysis only allows a crude estimate of the magnitude of the damage due to the

Learn More

(PDF) Methods to test and generate the wear load spectrum

Subsequently, the amplitude distribution of the wear load and its lasting time are extracted from the measured complex load-time history using the rain-flow counting method and Weibull distribution.

Learn More